Hypertherm MAX200 Machine Torch Plasma Arc Cutting System User Manual Page 33
- Page / 187
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
MAX200 Instruction Manual 3-5
14
SETUP
Adjusting the Filter/Pressure Regulator
To adjust the filter/pressure regulator for the required air pressure (90 psi) to the power supply:
1. Turn the Lock Knob, which secures the Adjusting Knob, counter clockwise (ccw).
2. Set the Adjusting Knob until the pressure gauge indicates 90 psi.
3. Turn the Lock Knob clockwise (cw) to secure the Adjusting Knob.
Additional Air Filtration
When site conditions introduce moisture, oil, or other contaminants into the air line, additional filtration is required.
Refer to Appendix A for filtration components and mounting sequence.
Gas Supply
Use inert gas hoses to connect the plasma and shield gas supplies to the gas input connectors on the rear of the
power supply.
Plasma Gas
To use liquid nitrogen, liquid oxygen, or argon/hydrogen as the plasma gas, it must be supplied to the MAX200 at
these purities: nitrogen, 99.995% and oxygen, 99.5%. The gas supply source can be compressed gas cylinders or
liquid containers. It must be capable of delivering the required gas at a delivery pressure of 120 psi to the power
supply. Refer to Section 4, Cut Charts for detailed information.
Note: If the purity level of the gas is too low or if there are leaks in the supply hoses or connections:
• Cut speeds can decrease
• Cut quality can deteriorate
• Cutting thickness capability can decrease
• Parts life can shorten
Shield Gas
To use liquid nitrogen or carbon dioxide (compressed or liquid) as the shield gas, it must be supplied to the
MAX200 at these purities: nitrogen, 99.995% and carbon dioxide, 99.5%. The gas supply source can be
compressed gas cylinders or liquid containers. It must be capable of delivering the required gas at a delivery
pressure of 90 psi to the power supply. Refer to Section 4, Cut Charts for detailed information.
- Machine Torch 1
- Plasma Arc 1
- Cutting System 1
- 800980 Rev 11 to 12 4
- Instruction Manual 6
- Hypertherm Plasma Systems i 8
- WARRANTY 9
- TABLE OF CONTENTS 10
- MAX200 Instruction Manual iii 10
- MAX200 Instruction Manual v 12
- Section 1 13
- ELECTRIC SHOCK CAN KILL 15
- Hypertherm Plasma Systems 1-3 15
- 1-6 Hypertherm Plasma Systems 18
- WARNING LABEL 18
- Section 1a 19
- SÉCURITÉ 19
- MISE À LA MASSE ET À LA TERRE 22
- Étiquette de sécurité 24
- Section 2 25
- SPECIFICATIONS 25
- Product Specifications 26
- MAX200 Instruction Manual 2-3 27
- CE Power Supplies 27
- 2-4 MAX200 Instruction Manual 28
- MAX200 Machine Torch 28
- Section 3 29
- Upon Receipt 30
- Pre-Installation 31
- Air Supply 32
- MAX200 Instruction Manual 3-5 33
- Additional Air Filtration 33
- Gas Supply 33
- Torch Coolant Requirements 34
- Power Supply Placement 35
- Routing the Torch Lead 35
- Power Requirements 36
- MAX200 Instruction Manual 3-9 37
- PRIMARY, 3 PHASE 40
- AC POWER CABLE 40
- Connect the Air and Gas Hoses 41
- Plasma Gas 43
- Supply Hose 43
- Shield Gas 43
- Grounding 44
- Remote Switch 48
- Assembly 48
- Machine Interface 48
- Cable (Fig. 3-10) 48
- Part No. Length 49
- Part No 60
- Adjust the Torch Position 64
- Section 4 66
- OPERATION 66
- Front Panel Controls 67
- MAX200 Instruction Manual 4-3 68
- Pre-operation 69
- Operation 69
- Operating Tips 70
- 4-6 MAX200 Instruction Manual 71
- MAX200 Instruction Manual 4-7 72
- Cutting Techniques 72
- 4-8 MAX200 Instruction Manual 73
- MAX200 Instruction Manual 4-9 74
- Cut Charts 75
- Do not use water muffler when 88
- 49-51 50-52 50 90 90 96
- 3.4-3.5 3.4-3.6 3.4 6.2 6.2 96
- 49-51 50-52 50 120 120 97
- 3.4-3.5 3.4-3.6 3.4 8.3 8.3 97
- 3/8 inch (10 mm) 100
- Water Tube 111
- Section 5 112
- MAINTENANCE 112
- Routine Maintenance 113
- Troubleshooting 113
- MAX200 Instruction Manual 5-3 114
- 5-4 MAX200 Instruction Manual 115
- MAX200 Instruction Manual 5-5 116
- 5-6 MAX200 Instruction Manual 117
- Replacement 117
- MAX200 Instruction Manual 5-7 118
- 5-8 MAX200 Instruction Manual 119
- Section 6 120
- PARTS LIST 120
- 6-2 MAX200 Instruction Manual 121
- MAX200 Instruction Manual 6-3 122
- 6-4 MAX200 Instruction Manual 123
- MAX200 Instruction Manual 6-5 124
- 6-6 MAX200 Instruction Manual 125
- MAX200 Instruction Manual 6-7 126
- 6-8 MAX200 Instruction Manual 127
- MAX200 Instruction Manual 6-9 128
- Recommended Spare Parts 135
- Machine Torch and Torch Leads 136
- Consumable Configurations 138
- Consumable Parts Kits 139
- Sleeve (Standard) 140
- Sleeve (Optional) 141
- Machine Torch Lead Assemblies 143
- Section 7 148
- WIRING DIAGRAMS 148
- Introduction 148
- Wiring Diagram Symbols 148
- 7-2 MAX200 Instruction Manual 149
- Torch Symbols 150
- 013179 013-2-179 013179B1 151
- N/A MAX200 1 OF 9 151
- BC 5-9-96 151
- 013179 013-2-179 013179B2 152
- N/A MAX200 2 OF 9 152
- POWER DISTRIBUTION 153
- PCB ASSY: 041534 153
- 013179 013-2-179 013179B4 154
- N/A MAX200 4 OF 9 154
- 013179 013-2-179 013179B5 155
- N/A MAX200 5 OF 9 155
- 013179 013-2-179 013179B6 156
- N/A MAX200 6 OF 9 156
- ELEC/GAS SCHEM: MAX200 157
- WIRED FOR 415 VAC 158
- 380-415/50 CE 158
- 013179 013-2-179 013179B9 159
- ITEM NO 160
- Appendix A 161
- Appendix B 170
- PROPYLENE GLYCOL SAFETY DATA 170
- BENZOTRIAZOLE SAFETY DATA 170
- Appendix C 180
- AERATION MANIFOLD 180
- Appendix D 182
- Power Cable 184
- Connect power cable 184
- 010297 REVA 185
- MAX200 Instruction Manual d-5 186
- Line Disconnect Switch 186
- EMI Filter Parts List 187
Related products and manuals for Equipment Hypertherm MAX200 Machine Torch Plasma Arc Cutting System
(211 pages)© 2020, manymanuals.com. All rights reserved. | 1.487 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals